MOONliteUSA - Instructions *WARNING - LIGHT EMITS INTENSE ULTRAVIOLET LIGHT. SHIELD EYES AND SKIN FROM LIGHT SOURCE. KEEP OUT OF REACH OF CHILDREN! DANGER - Connect to FUSED 12volt DC power source. Non-fused installation could result in FIRE, PROPERTY DAMAGE, or INJURY. PHONE JACK model does NOT have built-in fuse. CONNECT TO FUSED CIRCUIT ONLY. 1 amp fuse is sufficient for 1 light (5 amp max. per light). NEVER CONNECT TO AC POWER.DANGER / MANDATORY! TURN MOONlite OFF when under way. Law states when craft is under way between sunset and sunrise, no light shall be displayed that could be mistaken for, or interfere with view of coast guard approved navigation lights. Light could rotate and interfere with driver's vision.CAUTION! - DON’T RESTRICT AIRFLOW. High performance LEDs generate heat. The housing serves as a heat sink and is designed for minimum size while providing sufficient cooling. Depending on air flow, temperature and length of ON time, the housing could reach average temperatures of 125F. Light should turn OFF at 140F and turn back ON when case cools. If unit becomes excessively hot, thermal protection components are defective. If case temperature goes above 140F, turn off immediately and return for replacement. Hold light by plastic ends when hot.DON’T TWIST LIGHT TO RELEASE SUCTION CUPS! Lift edge of suction cups to release vacuum before attempting to remove light. Failure to release vacuum may result in broken phone jack connector. Broken connector is NOT covered under warranty.DON’T store in damp compartments or airtight containers.DON’T disassemble. Electronic components may be damaged by touch. Disassembly voids warranty.DON’T store near SALTY lures. Salt will corrode aluminum housing and power connections. Not recommended for saltwater use.DON'T break glass lens. Broken lens voids warranty. Beware of broken glass. OPERATING INSTRUCTIONS PHONE JACK - Install suction cups into nuts in T-slots. Remove dust and debris from cups and mounting surface. Place light into jack, taking care to hold light so connectors are properly aligned while pressing down to attach suction cups. Improper alignment or uneven pressure can break male connector. Adjust suction cup height so male connector is seated. Male connector may be slightly raised from fully seated position but no more than .100”. Depending on female connector height, it may be necessary to remove hex nut and shorten stud length or extend cup out as far as possible. Facing rear of light, main power switch is on left end. Full Moon visible light adjustment is a 2 way switch is on right end. Switching up sets visible light low, switching down turns light off, center sets light on high. LIGHTER PLUG - Install stud mount suction cups into T-slot nuts. Fuse located inside lighter plug. Switch operation same as phone jack model. COMMERCIAL - Acquire/install heat insulating handle for hand held applications. Fabricate custom hardware for permanent mounting. Cooling air circulation is required. T-slot nuts are size 8x32. Supply unit with regulated 12 to 13 volt DC. SWITCH OPERATION -FULL MOON - Facing rear of light, main power switch is on left end. Visible light switch on right end is a 3 position switch. Center position sets light to full power, down turns light off, up sets light to low.HALF MOON - Toggling up turns on both UV and green. Toggling down is UV only.LIGHT SHIELD INSTALLATION - Install one shield pin into hole in light's side plate. While holding down near pins on both ends of shield, lift at center of shield to cause bow in shield and insert second pin into other side plate. Release pressure and check for proper installation. Failure to support area near pins during installaiton may cause pins to break. TROUBLESHOOTINGAlways check light from a different power source such as a car's lighter plug socket for lighter plug models or a 12 volt battery pack for phone jack models. Phone jack tip is positive, phone jack barrel and light housing are negative.Light is weak - Supply voltage is less than 12 volts. Check for poor electrical connections, bad switch, or weak battery. Corroded phone jacks and fuse holders, rusty lighter plug sockets, corroded wire connections, corroded or loose battery terminals will cause low voltage. A good, properly charged battery will maintain 12 volts under normal loads.Light flickers - Poor connection at phone jack or lighter plug connector. Female connector is corroded or defective or connectors aren't fully seated.Light flashes on and off - Voltage is too high or light is overheated. TURN LIGHT OFF IMMEDIATELY - Continued use will damage light. Verify 12 volts and/or remove air flow restrictions.Light will not turn on - Check supply voltage at connector. Check phone jack height into female connector. Check fuse in lighter plug. Check light with a different power source. If all check good, main power switch may be defective. Switch off and on several times. If no light, return for replacement.Visible light will not turn on - LED or switch is defective. Switch off and on several times. If no light, return for replacement. Manufacturer, distributor, or retailer is NOT responsible for accident, injury, property damage, or loss due to use of this product.USE AT YOUR OWN RISK!- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -1 YEAR LIMITED WARRANTY – Repair or replacement. Physical damage or disassembly voids warranty! Email warranty inquiries to: info@moonliteusa.com MOONliteUSA, 471 Headtown Road, Jonesborough, TN 37659 Name___________________________________________________________________Phone number or email________________________________Address____________________________________________________________________________________________________________Store name and location _______________________________Problem____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

Instructions

*WARNING - LIGHT EMITS INTENSE ULTRAVIOLET LIGHT. SHIELD EYES AND SKIN FROM LIGHT SOURCE. KEEP OUT OF REACH OF CHILDREN!

DANGER - Connect to FUSED 12volt DC power source. Non-fused installation could result in FIRE, PROPERTY DAMAGE, or INJURY. PHONE JACK model does NOT have built-in fuse. CONNECT TO FUSED CIRCUIT ONLY. 1 amp fuse is sufficient for 1 light (5 amp max. per light). NEVER CONNECT TO AC POWER.

DANGER / MANDATORY! TURN MOONlite OFF when under way. Law states when craft is under way between sunset and sunrise, no light shall be displayed that could be mistaken for, or interfere with view of coast guard approved navigation lights. Light could rotate and interfere with driver's vision.

CAUTION! - DON’T RESTRICT AIRFLOW. High performance LEDs generate heat. The housing serves as a heat sink and is designed for minimum size while providing sufficient cooling. Depending on air flow, temperature and length of ON time, the housing could reach average temperatures of 125F. Light should turn OFF at 140F and turn back ON when case cools. If unit becomes excessively hot, thermal protection components are defective. If case temperature goes above 140F, turn off immediately and return for replacement. Hold light by plastic ends when hot.

DON’T TWIST LIGHT TO RELEASE SUCTION CUPS! Lift edge of suction cups to release vacuum before attempting to remove light. Failure to release vacuum may result in broken phone jack connector. Broken connector is NOT covered under warranty.

DON’T store in damp compartments or airtight containers.

DON’T disassemble. Electronic components may be damaged by touch. Disassembly voids warranty.

DON’T store near SALTY lures. Salt will corrode aluminum housing and power connections. Not recommended for saltwater use.

DON'T break glass lens. Broken lens voids warranty. Beware of broken glass.

OPERATING INSTRUCTIONS

PHONE JACK - Install suction cups into nuts in T-slots. Remove dust and debris from cups and mounting surface. Place light into jack, taking care to hold light so connectors are properly aligned while pressing down to attach suction cups. Improper alignment or uneven pressure can break male connector. Adjust suction cup height so male connector is seated. Male connector may be slightly raised from fully seated position but no more than .100”. Depending on female connector height, it may be necessary to remove hex nut and shorten stud length or extend cup out as far as possible. Facing rear of light, main power switch is on left end. Full Moon visible light adjustment is a 2 way switch is on right end. Switching up sets visible light low, switching down turns light off, center sets light on high.

LIGHTER PLUG - Install stud mount suction cups into T-slot nuts. Fuse located inside lighter plug. Switch operation same as phone jack model.

COMMERCIAL - Acquire/install heat insulating handle for hand held applications. Fabricate custom hardware for permanent mounting. Cooling air circulation is required. T-slot nuts are size 8x32. Supply unit with regulated 12 to 13 volt DC.

SWITCH OPERATION -

FULL MOON - Facing rear of light, main power switch is on left end. Visible light switch on right end is a 3 position switch. Center position sets light to full power, down turns light off, up sets light to low.

HALF MOON - Toggling up turns on both UV and green. Toggling down is UV only.

LIGHT SHIELD INSTALLATION - Install one shield pin into hole in light's side plate. While holding down near pins on both ends of shield, lift at center of shield to cause bow in shield and insert second pin into other side plate. Release pressure and check for proper installation. Failure to support area near pins during installaiton may cause pins to break.

TROUBLESHOOTING

Always check light from a different power source such as a car's lighter plug socket for lighter plug models or a 12 volt battery pack for phone jack models. Phone jack tip is positive, phone jack barrel and light housing are negative.

Light is weak - Supply voltage is less than 12 volts. Check for poor electrical connections, bad switch, or weak battery. Corroded phone jacks and fuse holders, rusty lighter plug sockets, corroded wire connections, corroded or loose battery terminals will cause low voltage. A good, properly charged battery will maintain 12 volts under normal loads.
Light flickers - Poor connection at phone jack or lighter plug connector. Female connector is corroded or defective or connectors aren't fully seated.
Light flashes on and off - Voltage is too high or light is overheated. TURN LIGHT OFF IMMEDIATELY - Continued use will damage light. Verify 12 volts and/or remove air flow restrictions.
Light will not turn on - Check supply voltage at connector. Check phone jack height into female connector. Check fuse in lighter plug. Check light with a different power source. If all check good, main power switch may be defective. Switch off and on several times. If no light, return for replacement.
Visible light will not turn on - LED or switch is defective. Switch off and on several times. If no light, return for replacement.

Manufacturer, distributor, or retailer is NOT responsible for accident, injury, property damage, or loss due to use of this product.

USE AT YOUR OWN RISK!

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

1 YEAR LIMITED WARRANTY – Repair or replacement.

Physical damage or disassembly voids warranty!

Email warranty inquiries to: info@moonliteusa.com

MOONliteUSA, 471 Headtown Road, Jonesborough, TN 37659

Name___________________________________________________________________

Phone number or email________________________________

Address____________________________________________________________________________________________________________

Store name and location _______________________________

Problem____________________________________________________________________________________________________________

___________________________________________________________________________________________________________________

Web Hosting by Yahoo!

info@moonliteusa.com

Instructions

﻿